bility
黏模型性，黏模性(壓鑄)stickness
黏砂clogging
黏土bond clay
黏土clay
黏土分試驗clay content test
黏土坩蝸clay crucible
黏土含量clay content
黏土黏結劑clay bond
黏土揉合機clay mill
黏土砂clay sand
黏土石墨混合劑clay-graphite mixture
黏土水clay wash
黏土水clay water
黏土磚clay brick
黏性，黏度viscosity
黏性砂(修爐用)sticky sand
黏性矽砂，山砂bonded silica sand
黏著adhere
黏著劑adhesive
黏著模砂adhering molding saand
黏著性adhesion
尿素甲醛樹脂urea-formal dehyde resin
捏泥砂機loam pug mill
鎳(Ni)nickel
鎳鋼nickel steel
鎳鉻鋼nickel-chromium steel
鎳鉻鈦鑄鐵Nicrosilal
鎳鉻矽球黑鑄鐵Nicrosilal spheronic
鎳黃銅nickel brass
鎳青銅nickel bronze
鎳銅合金cupro-nickel
鎳銅熱電偶合金constantan
鎳硬(鑄鐵)Ni-hand
鎳鑄鐵nickel cast iron
凝固freezing
凝固solidification
凝固點，冰點freezing point
凝固範圍freezing range
凝固收縮solidification contraction
凝固收縮solidifying contraction
凝固收縮率solidification shrinkage rate
凝聚cohesion
凝聚強度cohesive strength
凝析石墨kish graphite
凝析石墨斑孔kish graphite spots
凝析石墨夾渣(鑄疵)kish graphite inclusions
牛眼bull's eye
牛眼組織bull's eye structure
扭力試驗torsion test
扭轉，扭力torsion
歐氏氣體分析器Orsat-[gas] apparatus
排除，移動removal
排量式鼓風機positive displacement blower
排氣exhaust
排氣系統exhaust system
排氣煙道upstake flue
排顯孔(砂模)weep hole
排泄pop-up
排泄孔drain hole
盤pan
盤形輸送機pan-conveyor
判別試棒(展性鑄鐵及銅合金等爐前試驗)test sprue
刨屑shavings
泡面鋼blister steel
泡沫塑膠模型foam scrubber
泡沫洗淨器fly ash
砲銅gun metal
配料，攙合admixture
配料秤scale for charge make-up
配料機dosing machine
配料計算calculation of charge，calculating the charge
配料器dogage control unit
配料設施dosing device
配砂工場sand mixing plant
配置模型rigging
噴補gunning
噴補(熔爐)gun patching
噴補耐火料gunite
噴燈air bumer
噴燈，氣炬blast lamp，blow lamp
噴燈，氣炬blow lamp，blast lamp
噴燈，氣炬blow torch，blow lamp
噴敷料spraying mixture
噴光處理blast cleaning
噴壺shower
噴粒處理grit blast
噴粒機shot-blasting machine
噴泥槍clay gun
噴槍spray gun
噴砂sand blast
噴砂胴sand-blasting barrel
噴砂法sand-blasting
噴砂櫃sand-blasting cabinet
噴砂機sand-blaster
噴砂機sand-blasting machine
噴砂槍sand-blasting gun
噴砂設備sand-blast equipment
噴砂室sand-blasting chamber
噴砂裝置sand-blasting appaatus
噴砂嘴sand-blast nozzle
噴射injection
噴射jet
噴射成型機(塑膠)injection molding machine
噴射壓力injection pressure
噴射柱塞injection plunger
噴霧spray
噴霧，噴敷spraying
噴霧淬火foamed plastic pattern
噴霧淬火spray quenching
噴霧器sprayer
噴霧洗滌器spray jet scrubber
噴霧嘴atomization nozzle
噴修爐櫬法bondactor process
噴珠peening shot
噴嘴jet nozzle
噴嘴，注口nozzle
硼(B)boron
硼鋼boron steel
硼砂borax
硼酸boric acid
硼鐵ferro-boron
膨土bentonite
膨脹expansion
膨脹度degree of swelling
膨脹性expansibility
批，分次batch
鈹(Be)berllium
鈹青銅beryllium bronze
鈹銅Beryllium copper
皮氏管(測風用)pitch tube
皮下缺陷surface defect
皮下氧化surface oxidation
皮製內圓角leather fillet
皮重tare
疲勞fatigue
疲勞裂痕fatigue crack
疲勞破損fatigue failure
疲勞強度fatigue strength
疲勞試驗fatigue test
疲勞限界endurance limit
疲勞限界fatigue limit
片flake
片石墨鑄鐵flake graphite cast iron
片狀進模口slit gate
片狀石墨flake graphite
片狀石墨lamellar graphite
片狀石墨析出graphite flake precipitation
偏差deviation
偏晶monotectic
偏晶反應monotectic reaction
偏析segregation
撇渣separation of slag
撇渣skimming
撇渣包，撇渣瘤skim bob
撇渣口skim gate
撇渣流道siphon runner
撇渣冒口skim riser
撇渣器skimming tool
撇渣心型skimmer core
撇渣閘，撇渣器skimmer
撇渣磚skimmer brick
頻率變換器，週波變換器frequency converter
品質控制quality control
平底舂，平底搗桿flat rammer
平底搗鎚stamp
平底搗鎚，平底舂butt rammer
平放造模法mold on the flat
平刮[砂]strickling
平刮板drawing strickle
平刮板strickle
平刮板strickle board
平刮板臂strickle arm
平刮板導條strickle guide
平刮板模型，刮板模型strickle pattern
平刮板砂心盒strickle core box
平刮板支架strickle board support
平刮砂心strickling core
平衡equilibrium
平衡砂心balanced core
平衡砂心頭balance print
平衡送風熔鐵爐equilibrium-blast furance
平衡圖equilibrium diagram
平均粒度medium grain size
平爐open hearth furance
平爐Siemens-Martin furnace
平爐Siemens-Martin open hearth furnace
平爐法Siemens-Martin process
平爐鋼open hearth steel
平爐煉鋼法open hearth process
平木紋flat grain
平頭鏝刀flat trowel
平重，壓箱weighing
破斷強度rupture strength
破斷試驗rupture test
破壞模數modulus of rupture
破壞試驗destructive test
破裂，斷口fracture
破裂負載load to fracture
破裂區，破裂帶zone of fracture
普通灰[口]鑄鐵regular gray iron
普通石墨common graphite
普通碳common carbon
普通磚common brick
起吹blowing-in
起動器starter
起火燄pilot flame
起模stripping
起模板draw plate
起模板stripping plate
起模長針rapping spike
起模墊板rapping plate
起模釘draw nail
起模頂桿draw on pins
起模桿draw bar
起模機stripping machine
起模螺釘draw screw
起模螺釘lifting screw
起模斜度，通風draft，drautht
起模斜度，通風drautht，draft
起模型pattern drawing
起模針draw spike
起泡沫scumming
起熔塊starting block
起釉，變滑glazing
起重磁鐵lifting magnet
起重機，弔車cramne
汽車弔車motorised crane
汽車用鑄件automotive castings
汽化vaporization
砌澆(斗)，澆桶(斗)櫬料ladle lining
砌磚造模法brick molding
氣動搗鎚air rammer
氣動搗桿，氣動舂penumatic rammer
氣動搗砂pneumatic ramming
氣動弔車air hoist
氣動弔車pneumatic hoist
氣動工具compressed air tool
氣動工具pneumatic tools
氣動千斤頂pneumatic jack
氣動清砂，氣動清箱pneumatic knock-out
氣動射狂奔機air injection machine
氣割scarfing
氣化鎂magnesia
氣化鎂燒結物magnesia clinker
氣化鎂磚magnesia brick
氣炬，噴燈torch
氣炬噴燈torch lamp
氣炬硬化torch hardening
氣孔air hole
氣孔gas hole
氣孔(鑄疵)blow-hole
氣冷air cooling
氣力用具pneumatic appliance
氣力鑿pneumatic chipper
氣力震動造模機pneumatic jolt molding machine
氣路，風道air channel
氣泡air bubble
氣泡式吸應器bubble filter
氣槍air gun
氣熔刮(除去金屬表面缺陷)deseaming
氣體吹淨處理scavenging gas treatment
氣體發生器gas generator
氣體分析gas analyzing
氣體分析裝置gas analyzing apparatus
氣體熔接，氣焊gas welding
氣壓air pressure
氣鑿air chipper
氣障air bond，air lock
棄液let flow
千斤頂jack
牽鏈輸送機drag chain conveyor
牽條stay
鉛(Pb)lead
鉛青銅lead bronze
鉛銅cupro-lead
鉛煙氣lead fume
鉛浴 槽淬火lead bath quench
鉛浴槽lead bath
前端出渣front slagging
前爐fore blow
前爐receiver，fore-hearth
乾酪膠casein glue
乾模fired mold
乾模砂fired mold sand
乾砂模dry sand mold
乾砂模法dry sand molding
乾砂模鑄件dry sand castings
乾砂心dry core
乾砂心砂dry core sand
乾式集塵機dry mechanical dust collector
乾式施釉法dry enamelling
乾態強度dry bond strength
乾態強度dry strength
乾燥drying
乾燥，乾燥劑dehydrator
乾燥機drying machine
乾燥機，乾燥器，乾燥托板dryer，drier
乾燥劑desiccant
乾燥爐drying furance
乾燥爐drying oven
乾燥爐drying stove
乾燥器desiccator
乾燥器，乾燥劉drier
乾燥室drying chamber
乾燥收縮(砂模)dry shrinkage
乾燥塔tower drier
乾燥透氣性drying permeability
乾燥托板drying plate
淺出(金屬)splash
淺砂spillage sand ，spilling sand
潛變creep
潛變速率rate of creep
潛變限度creep limit
潛熱latent heat
嵌合模型fog quenching
嵌模板odd side board
嵌入bedding in
嵌入，內冷鐵insert
嵌入心型(壓鑄)knock-out core
強度strength
強化砂心頭strengthened core print
強力砂strong sand
強力鑄鐵high duty cast iron
強性黏土soapy clay
牆裝旋臂弔車wall creeper type jib crane
牆裝旋臂弔車wall jib crane
敲鎚rapping hammer
敲桿rapping bar
敲落員knock off personnel
敲模器rapper
敲鬆間隙(拔模型用)block print clearance
敲陷breaking in
敲型過度excess rapping
殼模shell mold
殼模吹造機shell mold blower
殼模對合機shell mold seatler
殼模法shell molding
殼模模型shell pattern
殼模砂心shell core
殼模壓合機shell mold press
殼模造模機shell molding machine
殼模鑄件shell mold castings
翹曲warp
翹曲warp warpage
翹曲warping
翹曲模型warped pattern
切斷機cut-off machine
切斷機cutter
切斷用砂輪abrasive cut-off wheel
切斷用砂輪，輪刀cutting wheel
切割砂輪slitting wheel
切線流道tangential runner
切削性machinability
切消袷度machining allowance
切屑borings
切屑chip
青銅bronze
氫(H)hydrogen
氫脆性hydrogen embrittlement
清(清砂、去毛邊等)fettle
清理fettling
清理場cleaning room
清理場fettling shop
清理工fettler
清理工具cleaning tool
清理工具fettling tool
清理門fettling door
清理

本文引用地址：http://www.weldr.net/weld_notes/html/content_858.htm

相关专题：焊接专业关联词汇（机械类）

来源：中国焊接资源网(http://www.weldr.net/)
作者：jql
原文：焊接专业关联词汇（铸造3）(http://www.weldr.net/weld_notes/html/content_858.htm)

[1] [2] [3] [4]

责任编辑：jql